HPI  |  160942

Flx-10 3S802 Flux Esc With Xt-60

£48.74
RRP: £49.99
Save £1.25
Home Delivery Available to order

        Allow 7-10 day(s) for order dispatch

The FLX10-3S802 Flux ESC is the perfect match for
the FLX10-3660-3700KV 1/10th scale brushless motor - it's
able to pump up to 80 amps of power to the motor for amazing
stunts, colossal top speeds, and wheel-spinning sideways
action!


Complete waterproof protection means you can take your truck
equipped with the FLX10-3S802 ESC into territory that would
scare off other drivers: puddles, mud, and more! A large fan sits
on top of the case inside a protective cover to keep things cool
when the weather's warm and you've been driving hard.


Technical Specifications:

Input Voltage: 2-3S LiPo

Continuous Current: 80A

Motor Limit: 2S LiPo <6000KV, 3S <3700KV

BEC: 6V Switching BEC, 3A Continuous Current

Battery Connector: XT60

Motor Connector: 4.0mm Bullet

Dimensions: 46x36.5x35.5mm

Application: 1/10th

Overheat Protection

Low Voltage Protection



Can be programmed using the Hobbywing LED Program Card



The FLX10-3S802 ESC & FLX10-3660-3700KV Motor requires
very powerful batteries to get the most out of them - please make
sure that you use the right combination! HPI highly recommend the
use of high-quality LiPo batteries. Using batteries with low
ratings, or the use of lower quality LiPo batteries, may cause
damage to your batteries and/or speed control. Using batteries
below the specified ratings may void the warranty of the speed
controller and/or batteries.


NOTE: Before driving in wet conditions, make sure that other
electronics fitted to the vehicle are safe to use (marked as
water-resistant or waterproof), or that they are fully enclosed and
protected from water and moisture (such as in a sealed
receiver/battery case). Fans mounted on speed controllers are not
water resistant - we recommend disconnecting the fan from the ESC
before driving in wet conditions and allowing it to dry fully
before reconnecting the fan power. Lubricate exposed metal
drivetrain parts such as bearings, outdrives and diff shafts before
driving in wet conditions. Motors are not intended for submerged
use and may be damaged if used when underwater. After driving in
wet conditions, make sure to rinse off dirt and any corrosive
liquids like saltwater with plain water and re-lubricate metal
drivetrain parts.

HPI

Flx-10 3S802 Flux Esc With Xt-60

£48.74

The FLX10-3S802 Flux ESC is the perfect match for
the FLX10-3660-3700KV 1/10th scale brushless motor - it's
able to pump up to 80 amps of power to the motor for amazing
stunts, colossal top speeds, and wheel-spinning sideways
action!


Complete waterproof protection means you can take your truck
equipped with the FLX10-3S802 ESC into territory that would
scare off other drivers: puddles, mud, and more! A large fan sits
on top of the case inside a protective cover to keep things cool
when the weather's warm and you've been driving hard.


Technical Specifications:

Input Voltage: 2-3S LiPo

Continuous Current: 80A

Motor Limit: 2S LiPo <6000KV, 3S <3700KV

BEC: 6V Switching BEC, 3A Continuous Current

Battery Connector: XT60

Motor Connector: 4.0mm Bullet

Dimensions: 46x36.5x35.5mm

Application: 1/10th

Overheat Protection

Low Voltage Protection



Can be programmed using the Hobbywing LED Program Card



The FLX10-3S802 ESC & FLX10-3660-3700KV Motor requires
very powerful batteries to get the most out of them - please make
sure that you use the right combination! HPI highly recommend the
use of high-quality LiPo batteries. Using batteries with low
ratings, or the use of lower quality LiPo batteries, may cause
damage to your batteries and/or speed control. Using batteries
below the specified ratings may void the warranty of the speed
controller and/or batteries.


NOTE: Before driving in wet conditions, make sure that other
electronics fitted to the vehicle are safe to use (marked as
water-resistant or waterproof), or that they are fully enclosed and
protected from water and moisture (such as in a sealed
receiver/battery case). Fans mounted on speed controllers are not
water resistant - we recommend disconnecting the fan from the ESC
before driving in wet conditions and allowing it to dry fully
before reconnecting the fan power. Lubricate exposed metal
drivetrain parts such as bearings, outdrives and diff shafts before
driving in wet conditions. Motors are not intended for submerged
use and may be damaged if used when underwater. After driving in
wet conditions, make sure to rinse off dirt and any corrosive
liquids like saltwater with plain water and re-lubricate metal
drivetrain parts.

View product
Back to top