Maverick  |  MV150634

Flx10-3S80 Flux Esc With Xt60 Plug


£67.39
RRP: £70.99
Save £3.60
Home Delivery Available to order

        Allow 7-10 day(s) for order dispatch

The FLX10-3S80 Flux ESC is the perfect match for
the FLX10-3660-3500KV 1/10th scale brushless motor - it's
able to pump up to 80 amps of power to the motor for amazing
stunts, colossal top speeds, and wheel-spinning sideways
action!


Complete waterproof protection means you can take your truck
equipped with the FLX10-3S80 ESC into territory that would
scare off other drivers: puddles, mud, and more! A large fan sits
on top of the case inside a protective cover to keep things cool
when the weather's warm and you've been driving hard.


Technical Specifications:

Input Voltage: 2-3S LiPo

Continuous Current: 80A

Burst Current: 540A

Motor Limit: 2S LiPo <600KV, 3S <400KV

BEC: 6V Switching BEC, 2A Continuous Current

Battery Connector: XT60

Motor Connector: 4.0mm Bullet

Dimensions: 50.5x56.2x35.4m (W/Fan)

Application: 1/10th Buggy/Monster Truck


The FLX10-3S80 ESC & FLX10-3660-3500KV Motor requires
very powerful batteries to get the most out of them - please make
sure that you use the right combination! HPI highly recommend the
use of high quality LiPo batteries. Using batteries with low
ratings, or the use of lower quality LiPo batteries, may cause
damage to your batteries and/or speed control. Using batteries
below the specified ratings may void the warranty of the speed
controller and/or batteries.


NOTE: Before driving in wet conditions, make sure that other
electronics fitted to the vehicle are safe to use (marked as
water-resistant or waterproof), or that they are fully enclosed and
protected from water and moisture (such as in a sealed
receiver/battery case). Fans mounted on speed controllers are not
water resistant - we recommend to disconnect the fan from the ESC
before driving in wet conditions and allow it to dry fully before
reconnecting the fan power. Lubricate exposed metal drivetrain
parts such as bearings, outdrives and diff shafts before driving in
wet conditions. Motors are not intended for submerged use and may
be damaged if used when under water. After driving in wet
conditions, make sure to rinse off dirt and any corrosive liquids
like saltwater with plain water and re-lubricate metal drivetrain
parts.

Download PDF instructions for #150634 (10.6 MB)

Maverick

Flx10-3S80 Flux Esc With Xt60 Plug

£67.39

The FLX10-3S80 Flux ESC is the perfect match for
the FLX10-3660-3500KV 1/10th scale brushless motor - it's
able to pump up to 80 amps of power to the motor for amazing
stunts, colossal top speeds, and wheel-spinning sideways
action!


Complete waterproof protection means you can take your truck
equipped with the FLX10-3S80 ESC into territory that would
scare off other drivers: puddles, mud, and more! A large fan sits
on top of the case inside a protective cover to keep things cool
when the weather's warm and you've been driving hard.


Technical Specifications:

Input Voltage: 2-3S LiPo

Continuous Current: 80A

Burst Current: 540A

Motor Limit: 2S LiPo <600KV, 3S <400KV

BEC: 6V Switching BEC, 2A Continuous Current

Battery Connector: XT60

Motor Connector: 4.0mm Bullet

Dimensions: 50.5x56.2x35.4m (W/Fan)

Application: 1/10th Buggy/Monster Truck


The FLX10-3S80 ESC & FLX10-3660-3500KV Motor requires
very powerful batteries to get the most out of them - please make
sure that you use the right combination! HPI highly recommend the
use of high quality LiPo batteries. Using batteries with low
ratings, or the use of lower quality LiPo batteries, may cause
damage to your batteries and/or speed control. Using batteries
below the specified ratings may void the warranty of the speed
controller and/or batteries.


NOTE: Before driving in wet conditions, make sure that other
electronics fitted to the vehicle are safe to use (marked as
water-resistant or waterproof), or that they are fully enclosed and
protected from water and moisture (such as in a sealed
receiver/battery case). Fans mounted on speed controllers are not
water resistant - we recommend to disconnect the fan from the ESC
before driving in wet conditions and allow it to dry fully before
reconnecting the fan power. Lubricate exposed metal drivetrain
parts such as bearings, outdrives and diff shafts before driving in
wet conditions. Motors are not intended for submerged use and may
be damaged if used when under water. After driving in wet
conditions, make sure to rinse off dirt and any corrosive liquids
like saltwater with plain water and re-lubricate metal drivetrain
parts.

Download PDF instructions for #150634 (10.6 MB)

View product